Quick Troubleshooting Guide for Flexographic & Rotogravure Printing Defects:
1. Marbled print, speckled or speckled appearance of the print, colored or black circles, most often appearing in light colors.
SR | CAUSE | REMEDY |
---|---|---|
1 | Viscosity too low | Add undiluted ink and adjust the viscosity. Change the photo. Add thickener. |
2 | Poor surface condition of the photo. Pollution of the photo (anti-foam, silicone, …) |
Thoroughly clean the plates, do not use materials likely to leave lint on the plate. |
3 | Poor condition of the bubbler or anilox. | Check the condition of the bubbler, the wear of the anilox cylinder, make sure that the cells are not blocked. |
4 | Ink absorption unevenly in the support. | Use softer shots, or opaque inks. Change media. |
2. The ink dries on the inking system (plate and cylinder) and hampers ink transfer.
SR | CAUSE | REMEDY |
---|---|---|
1 | Solvent-based ink: the diluting solvent evaporates too quickly. | Use a slower evaporating solvent (retarder). |
2 | Water based ink: incorrect pH. | Add 2-3% retarder. Add regenerator (1 to 2% every 3/4 hour). |
3. Drying too slow, tearing off the ink or smearing of the bar feeders. reel blocking, sticky ink.
SR | CAUSE | REMEDY |
---|---|---|
1 | Solvent-based ink: ink viscosity too high. | Use a slower evapor Reduce the viscosity with the recommended solvent. |
2 | Too slow evaporation of the dilution solvent | Use a faster evaporating solvent. |
3 | Water based ink: viscosity too high. | Dilute with water or viscosity reducer (2 to 5%). Incorporate regenerator (1 to 2%). |
4. Poor adhesion of the ink to the support, poor mechanical strength (crumpling, adhesive tape, scratching, etc.
SR | CAUSE | REMEDY |
---|---|---|
1 | Drying box problem. | Check temperature and extraction. |
2 | Ink not suitable for the medium. | Use suitable ink or consult the supplier. |
3 | Bad treatment of the support or outdated treatment. | Check the surface tension of the support or consult the supplier for the validity of the treatment. Check the appropriateness of applying a pre-lacquer varnish or primer or treating CORONA. |
4 | Insufficient drying. | Increase the drying temperature and if possible the air flow. |
5. Impression of intensity too low
SR | CAUSE | REMEDY |
---|---|---|
1 | Viscosity too low. | Add undiluted ink or a concentrate. |
2 | Anilox frame too fine. | Use an anilox with a larger weft. |
3 | Wear or blockage of the anilox frame. | Clean or change the anilox. |
6. Too intense impression
SR | CAUSE | REMEDY |
---|---|---|
1 | Viscosity too high. | Decrease viscosity with the appropriate thinner. |
2 | Anilox weft too large. | Choose an anilox with finer weft. |
3 | Wrong squeegee setting. | Adjust the squeegee to properly wipe the cylinder |
4 | Color strength too high. | Reduce the intensity with the appropriate bleach. |
7. Poor ink transfer, the plate does not deposit enough ink on the support.
SR | CAUSE | REMEDY |
---|---|---|
1 | Viscosity too low, drying on the plate. | Add undiluted ink. Adjust the ink drying. |
2 | Surface tension of the support too low or surface tension of the plate too high. | Check the treatment of the support and the surface energy of the plate. |
3 | Incorrect adjustment of the pressure between the radiograph and the anilox. | Adjust the settings. |
4 | Wear or blockage of the anilox frame. | Change or clean the anilox. |
5 | Anilox frame too fine. | Use a larger weft. |
8. Poor ink transfer, the plate does not deposit enough ink on the support.
SR | CAUSE | REMEDY |
---|---|---|
1 | Viscosity too low, drying on the plate. | Add undiluted ink. Adjust the ink drying. |
2 | Surface tension of the support too low or surface tension of the plate too high. | Check the treatment of the support and the surface energy of the plate. |
3 | Incorrect adjustment of the pressure between the radiograph and the anilox. | Adjust the settings. |
4 | Wear or blockage of the anilox frame. | Change or clean the anilox. |
5 | Anilox frame too fine. | Use a larger weft. |
9. Increase in viscosity in the inkwell / duct
SR | CAUSE | REMEDY |
---|---|---|
1 | Solvent-based ink: unsuitable solvent or imbalance due to evaporation | Add undiluted ink. Adjust the ink drying. |
2 | Water-based ink: decrease in pH. | Add regenerator (1 to 2%). |
10. Blurring of Four Color Print
SR | CAUSE | REMEDY |
---|---|---|
1 | Poor relationship between the screen size and that of the anilox | Select an anilox suitable for the work to be performed. In flexo the ratio between the frame of the plate and that of the anilox must be from 1 to 3.5 or even 4 |
2 | Wrong angle of the screen frames | Selection films must be corrected. |
11. Blocking in reel, adhesion of the turns between them making the prints unusable, transfer of the front printing on the back of the support.
SR | CAUSE | REMEDY |
---|---|---|
1 | Poor ink drying. | Reduce the viscosity of the ink. Change the dilution solvent to speed up drying. Change the proportion of the dilution solvent, Increase the drying capacity and / or the air volume. |
2 | Rewind too tight. | Reduce the rewind tension. |
12. Excess ink around halftone dots and small text and poor character definition.
SR | CAUSE | REMEDY |
---|---|---|
1 | Excess pressure between the radiograph and the anilox. | Set the pressure correctly |
2 | Ink drying too fast | Adjust the ink drying. |
3 | Viscosity too high | Decrease viscosity. |
13. Streaks, large transverse lines on the print.
SR | CAUSE | REMEDY |
---|---|---|
1 | Worn gear | Replace worn gears. |
2 | Over-tightening of the ink cylinder. | Over-tightening of the ink cylinder. |
3 | Viscosity too high | Decrease viscosity. |
Still Facing Issues?
The most common causes for different print defects are explained below:
EXCESSIVE DOT GAIN:
Dot gain occurs in every print. In fact, the essence of flexographic printing. But you have a problem when it becomes too much.
Appearance: Images appear darker and sometimes less high-resolution than intended.
Most likely causes: You may simply have too much pressure between the printing sleeve/cylinder/plate and the substrate. Try a “kiss” impression, and if pressure is really the issue, your dots should return to normal. Another likely cause is thick or swollen sleeves or plates from aggressive inks, solvents, and/or cleaning agents. You can avoid swelling by choosing in-the-round (ITR) elastomer sleeves, which are extremely durable and resistant to swelling.
Here are some other potential causes:
- Incorrect ink viscosity
- Too much anilox cell volume
- Dots dipping into the anilox (cell count too low)
- Press damage or wear
- Dirty image carrier
- Mounting tape has the wrong thickness or trapped air, if using plates
GEAR MARKS:
This is often also called gear chatter or banding. Avoiding this flexo printing defect involves routine press monitoring and maintenance. In short: Machinery wears and breaks down, and it’s critical to keep it up.
Appearance: Alternating lines of light and dark that typically run perpendicular to the web’s direction on the press.
Most likely causes: Gear marks stem from press mechanics and too much pressure. Within those 2 key indicators, however, are a host of other potential issues that could hurt your printing quality. The good news is gear marks (or chatter) are sometimes clearly audible on your press.
Gears wear over time, with teeth eroding away and even breaking. Improperly sized gears won’t mesh correctly and will cause imbalance and bouncing.
Other potential causes:
- Poor drive gear lubrication
- Pressure tolerances between elastomer and photopolymer sleeves/plates
- Inadequate cleaning
HALO:
Flexographic printing is a pressure-sensitive process. Fittingly, the halo effect is one of 9 common flexo printing defects we recognize with pressure as a likely cause.
Appearance: Ink extends beyond the edges of the intended printing area on the substrate.
Most likely causes: Too much pressure pushes ink out because it has no other place to go. Irregular pressure could be apparent if the severity of the halo differs from one location to another on the substrate. Lower and otherwise adjust the pressure from the print cylinder to the substrate as a possible solution.
Other potential causes:
- Too much ink transfer
- Cylinder-to-web speed mismatch
FEATHERING:
While too much pressure also predominantly causes this flexo defect, there could be a host of other sub-issues making your prints look unprofessional.
Appearance: Ink extends beyond the intended printing area to create uneven edges, which look quite like the hairlike projections of a bird’s feather.
Most likely causes: Ink builds up around dots and inadvertently increases the printing surface area. You could be experiencing too much pressure between the print cylinder and the substrate or between the anilox and print cylinder earlier in the process.
Other potential causes:
- Dried ink on the image carrier
- Debris on the substrate
- Ink drying too quickly
- Ink surface tension too high
DOUGHNUTS:
This flexo printing defect is no delicious confectionery treat. It’s an aggravating and potentially expensive problem to experience.
Appearance: Screen dots come out slurred and distorted with blank or semi-blank spaces in the middle. They look like lopsided doughnuts.
Most likely causes: While pressure is another potential root cause of doughnuts, the most likely culprit is actually cylinder or plate swelling. Aggressive inks and solvents can wreak havoc with printing products, causing them to swell and distort to, in turn, make images nearly unrecognizable. Switching to more solvent-resistant, direct-laser engraved (DLE) ITR elastomer sleeves is a potential solution.
Other potential causes:
- Pressure
- Print-to-web speed conformity
- Ink transfer
SKIP OUT:
Your ink must wet out completely on the substrate (in essence, excellent ink transfer) Press mechanics play a vital role in that equation. If you have wobbling, in particular, parts of the printing form will contact the substrate unevenly. But you may also be experiencing other issues from ink composition to thorough maintenance and cleaning.
Appearance: Prints come out with sections that are either too light or missing entirely.
Most likely causes: Even seemingly the smallest resonant vibrations and other issues with press mechanics can impact how well the print cylinder contacts the substrate. Any unintended movement of press components can easily cause skipout.
Other potential causes:
- High or low areas on the image carrier, bent shafts, or out-of-round components
- Ink surface tension and substrate surface energy
- Pressure
- Ink viscosity and pH
- Routine maintenance and cleaning
MISREGISTRATION:
Great flexographic quality requires precise alignment of ink combinations on the substrate. Even if it’s off by a small fraction of an inch, your design accuracy and color patterns will be incorrect.
Appearance: Certain colors or design elements don’t align, causing color shifting, cracks between colors, or blurred-over prints.
Most likely causes: Incorrect plate position or orientation. Each plate or separation must be aligned exactly for an excellent print.
Other potential causes:
- Impression cylinder concentricity
- Cylinder/plate/sleeve condition
- Gear condition
- Idle rollers dragging or rotating irregularly
- Malfunctioning web guide
- Web growth or fanning out
- Wandering web
- Substrate tension
- Incorrect tolerances
MOTTLED IMAGE:
This flexographic defect plagues package printing that requires a lot of solid color imagery. Essentially, in these cases, ink is not wetting out fully on the substrate.
Appearance: Printed areas intended to have solid color have noticeable unevenness in print density and shade/hue variations. This appears bumpy and has the visual consistency of an orange peel.
Most likely causes: Poor ink transfer between the anilox, image carrier, and substrate are causing variations in print density. This often begins with selecting an anilox with the proper cell count/cell volume and making sure all ink-transferring elements on your press are clean.
Other potential causes:
- Surface tension
- Ink viscosity
- Pressure
- Damaged or contaminated image carrier, ink, or substrate
BRIDGING/FILLING-IN:
Although these are technically separate, these 2 similar flexo printing defects can be considered as one. Basically, a variety of factors could be allowing too much ink on the image carrier.
Appearance: Letters or intricate areas within graphics bleed together for a low-quality, low-resolution image. In bridging, closely spaced design elements connect with each other irregularly. In filling in, excess ink accumulation fills in spaces that weren’t supposed to be printed.
Most likely causes: Pressure and press mechanics could easily push ink where it doesn’t belong. Lighten the load on the substrate with a “kiss” impression.
Other potential causes:
- Anilox cell volume/cell count and/or engraving angle
- Ink viscosity
PINHOLING:
Some areas of your substrate don’t print fully. This one has a very distinctive, incomplete look.
Appearance: Tiny unprinted spots about the size of a pinhole.
Most likely causes: Among the potential culprits, you may have a dirty anilox causing poor ink transfer. Ink may be drying too quickly, causing it to pick off the substrate.
Other potential causes:
- High ink viscosity
- Anilox has lost cell volume
- Irregular or damaged substrate surface
- Incorrect surface tension chain, most likely between the image carrier and substrate
DIRTY PRINT:
With a variety of potential causes, this defect greatly impacts image quality in high resolution areas.
Appearance: Speckles in the ink that give it a dirty appearance or evidence of excessive dot gain.
Most likely causes: The defect’s namesake: Dirt. Airborne contaminants surround us everywhere we go, particularly in an active industrial printing press room. Working machinery promotes static electricity, which attracts floating dust, paper particles, and other contaminants to your ink, anilox, image carrier, and/or substrate.
Other potential causes:
- Drying ink
- Incorrect ink viscosity
- Improper anilox
- Non-uniform substrate